PARAMETER;MIN;TYP.;MAX;UNIT

Operating Frequency;9400;;9460;MHz IF Filter Bandwidth of receiver 3dB;60;60;60;MHz No. of Tx / Rx Channel;;1;;-- Peak Output Power / Channel;;47;;dBm Transmit Gain @ In all frequency/temps.;;47;;dB Tx input Power;;0;;dBm Second Harmonic of TX;;< -25;; dBc Pulse Width;0..1;;300;us Max Duty Cycle;;;25;% Pulse Droop;<0.5 (For 300 us pulse width);;;dB Fall Time;;100;;ns Raise Time;;100;;ns Transmit Channel Output ON/OFF Ratio;>110;>110;>110; dBc Power Added Efficiency;＞25 %;＞25 %;＞25 %; VSWR (TX IN, ANT IN, RX OUT Ports);;1.8:1;;-- Rx Gain;;50;;dB Rx Output P1dB;;≥10;;dBm RX Input P1dB;;-15;;dBm Rx Noise Figure(0 dB Attenuation State);;3.5;4;dB Rx Noise Figure(15 dB Attenuation State);;;6;dB IF Filter Ripple;< 1 dB;< 1 dB;< 1 dB;Ripple in ±10Mhz around 75Mhz Receiver Channel Image Rejection;>30;>30;>30; dBc Receiver Output in Band Spurious Rejection;>60 (Measured for +8 dBm output power);>60 (Measured for +8 dBm output power);>60 (Measured for +8 dBm output power); dBc Receiver Output Out of Band Spurious/Harmonics Rejection;>50 (Measured for +8 dBm output power);>50 (Measured for +8 dBm output power);>50 (Measured for +8 dBm output power); dBc Attenuator;6 bits;6 bits;6 bits;0~31.5 dB Attenuator Accuracy;< 1.7 (RMS);< 1.7 (RMS);< 1.7 (RMS);dB Maximum Phase Change of Receiver Channel vs Attenuator States;<15°;<15°;<15°;31.5 dB Attenuation State Maximum Phase Change of Receiver Channel vs Attenuator States;<5°;<5°;<5°;10 dB Attenuation State LO Frequency;;9310;;MHz Transmit Input to Receiver Output Isolation;>50;>50;>50;dBc Max. Rx tolerable power;;≥50W;;Max duty cycle Power Supply;;28;;V Average currents;;;1.75 @ DUC25%;A Peaking currents;;;7;A Protection against open output connector;;Important, Design Guarantee;;-- Temperature reporting;;Please use TMP36 IC for temperature (analog devices);;--

PARAMETER;VALUE;UNIT

Dimensions (L x W x H);160 x 120 x 30;mm RF Connectors (Input / Output);SMA-K /SMA-K;-- DC /Control Connector;J30J – 21ZK;-- Weight;≤1.5;Kg

PARAMETER;MIN-MAX;UNIT

Operating Temp. (Housing Temp.); -40;+65;°C Humidity Range;0;100;% PA Baseplate Shutoff Temperature;+ 80;;°C

AMPLIFIER CONNECTOR TYPE:;J30J – 21ZK TRIAD CABLE PART NUMBER:;—— NUMBER;DESCRIPTION

1,12,2,13;+28V 3,14,4,15;GND 5;SEL (TTL 5v) 16;R (TTL 5v) 6;Load (TTL 5v) 17;T (TTL 5v) 7;Data (TTL 5v) 18;CLK (TTL 5v) 8,9,19;GND 10;Monitor voltage of Temperature 21;NC 11,20;NC

Detailed info for power supply types as Table 2 Voltage;Limit Voltage (V);Working Voltage Range (V);Ripple wave (mV, ppm) Voltage ;min;max;min;max;Ripple wave (mV, ppm)

+28V;-;+29;+27.5;+28.5;100

Table 4 Definition for serial data Order;;Function;Remarks;

D0～D1;Set 01;01;; D2;RX Standby Control;;Low level standby, RX not working, High level，RX normal D3～D8;Set 000000;000000;; D9;Rx ATT;Rx Attenuation Control;-0.5dB;High level valid IN IF D10;Rx ATT;Rx Attenuation Control;-1dB;High level valid IN IF D11;Rx ATT;Rx Attenuation Control;-4dB;High level valid IN IF D12;Rx ATT;Rx Attenuation Control;-16dB;High level valid IN IF D13;Rx ATT;Rx Attenuation Control;-8dB;Low level valid IN RF D14;Rx ATT;Rx Attenuation Control;-2dB;Low level valid IN RF D15;TX ATT;Rx Attenuation Control;-0.5dB;High level valid D16;TX ATT;Rx Attenuation Control;-1dB;High level valid D17;TX ATT;Rx Attenuation Control;-4dB;High level valid D18;TX ATT;Rx Attenuation Control;-16dB;High level valid D19;TX ATT;Rx Attenuation Control;-8dB;High level valid D20;TX ATT;Rx Attenuation Control;-2dB;High level valid D21～D26;Set 000000;000000 D27;TX Stand by Control;;Low level standby, Tx not working, High level，Tx normal